LDA full form

What is the full form of LDA?

Answer:

  • Local Density Approximation

What does LDA mean?

The LDA assumes that the density variations are slow and treats the local density as if it were a uniform electron gas.

LCB full form

 What is the full form of LCB?

Answer:

  • Linear Current Booster

What does LCB mean?

For solar direct water pumping systems, LCB is nearly essential. When the solar panels aren't producing enough current for the pump to which they are connected, a linear current booster converts excess solar PV voltahe into extra amperage. LCBs will increase water delivery by 20% or more in most solar direct systems, and we usually recommend a properly sized onw with every system.

EPCS full form

What is the full form of EPCS?

Answer:

  • Electronics Prescribing For Controlled Substance

What does EPCS mean?

EPCS is intended to replace paper prescriptions by allowing clinical prescribers to write controlled substance prescriptions electronically, making these prescriptions digitalized and trackable for both the prescriber and the pharmacy. 

ERT full form

What is the full form of ERT?

Answer:

  • Emergency Response Time

What does ERT mean?

ERT is critical  that the healthcare organization provide the resource necessary to effectively respond to critical incidents in order to provide excellent patient care and ensure the safety of staff and visitors. These incidents could be criminal in nature, or they could be caused expouse to hazardous materials, bad weather, fires or accidents.


OLC full form

What is the full form of OLC?

Answer:

  • Open Loop System

What does OLC mean?

An OLC is a type of control system in which the system output is dependent on the inputt but the input or controller is independent of the system output. Becuase these systems lack a feedback loop they are also known as a non feedback systems.

OCV full form

 What is the full form of OCV?

Answer:

  • Open Circuit Voltage

What does OCV mean?

The difference in electrical potential between two terminals of a device when it is disconnected from any circuit is referred to as a OCV. There isn't anything connected to the outside world. There is no external electrical current following between the terminals.

GEICS full form

What is the full form of GEICS?

Answer:

  • Georgia Electronics Insurance Compliance System

What does GEICS mean?


The GEICS is a database of all motor vehicles in the US state of Georgia, as well as the current liability insurance carried by their drivers. It was establshed during the 2002 session of the georgia general assembly to reduce the number of uninsured motorists. 


LPCVD full form

 What is the full form of LPCVD?

Answer:

  • Low-Pressure Chemical Vapor Deposition

What does LPCVD mean?

LPCVD is a type of chemical vapor deposition that uses heat to start a reaction between gas and solid substract. The solid phase material is formed as a result of the reaction at the surface. LP is is used to reduce any undesirable gas phase reactions while also increasing uniformity across the substrate.

LIB full form

 What is the full form of LIB?

Answer:

  • Lithium-Ion Batteries

What does LIB mean?

LIB appears to be popular. This is primarily due to the battery's ability to be deployed in a variety of locations. Lithium ion batteries have many applications, ranging from a small smartphone battery to large sophisticated batteries used in electric automobiles.


LEEP full form

 What is the full form of LEEP?

Answer:

  • Electrosurgical Excision Procedure

What does LEEP mean?

The LEEP removes cells and tissue in a woman's lower genital tract by heating a wire loop with an electric current. It is used in the diagnosis and treatment of abnormal or cancerous conditions.

FPA full form

 What is the full form of FPA?

Answer:

  • Focal Plan Array

What does FPA mean?

The FPA is a type of bolometer that serves as a thermal detector in infrared cameras, The FPA is built around a matrix of a small thin-film bolometer arranged in the focal plane of the detector. This results in a planar pixel sensor, which allows for a better price-performance ratio in a variety of applications.


IPEM full form

 What is the full form of IPEM?

Answer:

  • Integrated Power Electronics Module

What does IPEM mean?

IPEM is a solid-state electronics is used in power electronics to control and convert electric power. The goal of power electronics is to convert power from an electrical source to an electrical in a highly effiecient, dependable and cost effective manner. Power electronics modules are essientail components of a power electroinci system. Power switch and associated electronic circuitry for drive control and protection as well as other passive components are integrated into these modules.




IMSE full form

What is the full form of IMSE?

Answer:

  • Injection Molded Structural Electronics

What does IMSE mean?

IMSE is a smart molded structure is created by integrating and encapsulating printed electronic and standard components within the 3D injection-molded plastics that are both durable and long lasting. IMSE technology validation distince from traditional electronics. IMSE technology validation process also include extensive reliability testing to ensure the dependability of IMSE solutions.

IED full form in electrical engineering

What is the full form of IED?

Answer:

  • Intelligent Electronic Device

What does IED mean?

IEDs have recently been widely deployed in power automation systems, and the transition from RTUs to IEDs is evident due to the IEDs integrations and interoperability features. This technical article explains the IED advanced functionality briefly in order to present a comprehensive view of automation in power systems.

CCEG full form

 What is the full form of CCEG?

Answer:

  • Commonwealth Centre for Electronic Governance

What does CCEG mean?

The CCEG is a think tank based in London, Uk that operates under the auspices of the commonwealth's secretariates e-governance programme. The commonwealth centre for electronic governance mission is to provide insight and knowledge on the changing nature of governments in our rapidly expanding technological infrastructures.

CATR full form

 What is the full form of CATR?

Answer:

  • Compact Antenna Test Range

What does CATR mean?

A CATR allows electrically large antennas to be measured at a much shorter distance than a traditional far-field test range would require. A source antenna radiates a spherical wave in the direction of a parabolic collimating it into a planer wave for aperture illumination of a device under test in compact range. The size of the reflector its edge treatment, and the absorbers all influence its lowest operational frequency.

IEM full form

 What is the full form of IEM?

Answer:

  • Industrial Electric Manufacturing

What does IEM mean?

IEM is the US largest independent full-time manufacturer of electrical distribution equipment and integrated power systems. IEM has been delivering customer-specific solutions to meet the ever-changing power requirement of North American growth industries for over a half-century.


CDW full form

 What is the full form of CDW?

Answer:

  • Charge Density Wave

What does CDW mean?

A CDW is a static modulation of conduction electrons that is caused by a Fermi surface. It is usually accompanied by a periodic distortion of the lattice, The distortion reduces the solids electronic energy, and the associated strain's energy is more than compensated by the reduction in electronic energy. 

CEPT full form

What is the full form of CEPT?

Answer:

  • Concealed Electrical Power Transfer

What does CEPT mean?

The heavy-duty, tamper-resistant CEPT securely transfers power and data from the hinge side of the frame to the door's electrified hardware. When the door is closed, the unit is concealed between the frame and the door. The CEPT complements any architectural setting and is available in three multi-wire configurations and four finishes.



CPRM full form

What is the full form of CPRM?

Answer:

  • Content Protection for Recordable Media Specification 

What does CPRM mean?


The CPRM specifies a method for protecting content recorded on a variety of physical media types. The 4C Entity, LLC created it as a type of digital rights management.




EDI full form

What is the full form of EDI?

Answer:

  • Electronic Data Interchange

What does EDI mean?

EDI is the intercompany exchange of business documents in a standard format. EDI is a standard electronic format that replaces paper-based documents such as purchase orders and invoices. Organizations can save time and eliminate costly errors caused by manual processing by automating paper-based transactions.


LFU full form

What is the full form of LFU?

Answer:

  • Least Frequently Used

What does LFU mean?

LFU is a cache algorithm that is used to optimize computer memory. The system keeps track of how many times a block is referred to in memory using this algorithm. When the cache memory is completely full and more space is required, the item with the lowest reference frequency is deleted.

GUI full form

What is the full form of GUI?

Answer:

  • Graphical User Interface

What does GUI mean?

GUI is refer to the graphical interface that allows users to interact with electronic devices such as computers and tablets. It displays information through icons, menus and other graphical representations rathaer than text based commans. User can use the graphic elements to give commands to the computer and select functions by usinf a mouse or other input devices.

ATMEL full form

What is the full form of  ATMEL?

Answer:

  • Advanced Technology For Memory and Logic

What does ATMEL mean?

ATMEL was a semiconductor designer and manufacturer based in San Jose, California, in the US. Advanced technology for memory and logic is a company's income; focus.



RFID vs NFC | Difference, Comparison & Real-World Examples

RFID and NFC are used daily by our customers for cashless payment, access control, social networking, and experiential marketing. It is quick, friendly, engaging, and dependable, albeit a little perplexing which is why we are here to help. So here this article gives the difference between RFID and NFC to better understand this topic.

What is NFC?

NFC stands for near-field communication, it is wireless communication technology that is primarily used in mobile or handheld devices. It allows radio communication to be established by touching two phones or keeping them within a few centimetres of each other. It is simple to select for the last few centimetres. NFC communication is primarily based on induction coupling, which uses magnetic induction between two loop antennas operating at a frequency of 13.56 MHz and data rates ranging from 106 to 424kbit/s.

What is RFID?

RFID stands for radio frequency identification, It is a method that makes use of the internet. Data is digitally encoded in RFID tags that can be read by a reader, similar to barcodes, and data read from tags is stored in a database by the reader. It is made up of two parts: an integrated circuit and an antenna, and the tags are protected by a layer of material that acts as a shield against various environmental effects. The most commonly used RFID tags are passive and active RFID tags.

Difference between RFID and NFC | RFID vs NFC:

Developed:

NFC called near-field communications is introduced in 2002, while RFID called frequency identification technology is introduced in 1980.

Definition:

NFC is a type of short-range high-frequency wireless technology and is mainly used for mobile or handheld devices. While radio frequency identification is an automatic identification method that uses the internet, in which data is digitally encoded in RFID.

Tags:

NFC is near field communication tags that are passive in nature. While RFID identification tags can be both active or passive in nature and also semi-passive in nature.

Communication:

NFC provides bidirectional communication, while RFID unidirectional communication.

Structure:

NFC in which only for smartphones with in-built communication, while the RFID we have to add some extra tags and a reader.

Security:

NFC provides medium security features,  while RFID provides features like miss reading duplication or basic security. 

Sampling:

Sampling is not present in radio frequency in NFC, while RFID sampling is not present.

Frequency range:

In NFC we operate only high frequency 13.56 MHz and act ac both reader and tag devices must be in close proximity due to short read range. While RFID identification contains three types of range. low frequency: 125-134 Khz, high frequency - 13.56 Mhz, Ultra high frequency - 856 MHz to 960 Mhz.

Popular Uses:

NFC tags are generally used for paying bills using NFC, tracking car mileage, sharing data, and sharing and transferring information between two devices by tapping each other, while the RFID tags are generally used for asset tracking, tools tracking, race timing, access control, and inventory tracking.

Explore more information:

  1. Difference between Bluetooth and Zigbee
  2. Difference between Wi-Fi and Bluetooth
  3. Difference between 2G-GSM and 3G-WCDMA
  4. Difference between GSM and UMTS
  5. Difference between DSSS and FHSS
  6. Difference between GSM and GPRS 
  7. Difference between GPRS and EDGE
  8. Difference between GSM and GPS
  9. Difference between FDMA and TDMA

WiFI vs Broadband | Difference | Comparison

Broadband and WiFi are two terms that are frequently used interchangeably. However, these are two distinct concepts that must be clearly understood in order to master the fundamentals of the internet. So let us check the difference between wifi and broadband to better understand this topic.

What is WiFi?

WiFi stands for wireless technology that connects devices to the internet. While this internet connection can be either broadband or dial-up, wifi is the most commonly used to connect to a broadband internet line. A WiFi network, which allows multiple devices to connect to a single internet access point, is simple to set up using a wireless modem or router. 

What is Broadband?

Wireless broadband uses a radio link between the customers, location, and the services provider's facility to connect a home or business to the internet. Wireless broadband, which refers to high-speed broadband delivered wirelessly from a service provider to a location, can be mobile or fixed.

WiFI vs Broadband | Difference between wifi and broadband:

Definition:

WiFi is wireless connectivity that uses radio waves to provide an internet connection, while Broadband is open connectivity in which a high-speed internet connection is always available.

Portability:

Wifi is having great portability, while the Broadband is having fewer portability features.

Network:

WiFi is more network blocking can be faced in this, while Broadband is less network blocking can be faced in this.

Expensive:

WiFi is very expensive, Broadband is less expensive.

Replies:

WiFi relies on the original devices that produce the internet, while Broadband doesn't rely on the original devices, it has the capacity to provide higher internet connectivity.

Connection device:

WiFi connects the device to home and business networks, while broadband connects those networks to the internet.

Technology:

802.11a, 802.11b, 802,11g, and 802,11n are four major types of WiFi technology, while the DSL, cable, fiber, and satellite are four common forms of broadband.

Explore more information:

MOSFET vs FinFET

Despite belonging to the same transistor family, FinFET and MOSFET are constructed differently and have different levels of scalability. Let us take a closer look at these two-transistor to better understand the differences between FinFET and MOSFET.

What is MOSFET?

The term MOSFET in full form is Metal-Oxide-Semiconductor-Field-Effect-Transistor. MOSFET is one type of power transistor device mostly used in VLSI circuits, CMOS digital circuits, microprocessors, memory devices, etc.

Learn more about NMOS vs CMOS

What is FinFET?

FinFET stands for the fin-shaped field-effect transistor. A FinFET is a type of transistor. It is both an amplifier and a switch because it is a transistor home computer, laptops, tablets, smartphones, wearables, high-end networks, automotive and other device are among its applications. FinFET is a nonplanar device, which means it is not limited to a single plane. It is also known as 3D because it has a third dimension.

Difference between MOSFET and FinFET:

Drive strength:

The drive strength of a planner MOSFET is determined by the channel width, whereas the drive strength of a FinFET can be increased by incorporating multiple or longer fins.

Speed:

Fast switching times in FinFET can be attributed to a higher drive current. otherwise, three-dimensional FinFET is a high-speed device when compared to planar MOSFETs.

Construction

FinFET technology makes it simple to create multi-gate devices. In MOSFET planner construction makes multi-gate construction difficult.

Leakage current

In switching devices, leakage power is caused by leakage current and leakage voltage. FinFET has a low leakage current, its power consumption is lower than that of MOSFET.

Leakage power

The length of the gate has a significant impact on reducing leakage current as a result of leakage power. FinFET has sufficient gate length because the gate is wrapped around the drain-source channel, and there is no leakage current when the gate is not energized.

Scalable

A large number of transistors can be housed on a single chip. FinFET technology is suitable for IC fabrication because it is more scalable per footprint area than MOSFET.

Applications

Channel doping is commonly used in planar MOSFET to improve short-channel behavior. Channel doping in FinFET is due to optional due to the wrap-around gate over the thin body, there are dopant-induced fluctuations in FinFETs.

Size

Transistor shrinks as chips are reduced in size, because of this compactness, the drain and source are closer together, and the gate control over the channel carries is reduced. This type of short channel effect has the potential to cause serious problems in MOSFET.

Outperforms planar 

FinFET outperforms planar MOSFET in terms of subthreshold slope and voltage gain.

Difference between mass and volume

The difference between mass and volume is that mass is the amount of matter that an object is composed of whereas volume is the amount of space that an object occupies. The weight in the mass product, as well as the mass and volume, are directly related. Light has no mass or volume which is a converging fact. So let us check the difference between mass and volume to better understand this topic.

What is Mass?

The mass is volume dependent and is simply an object accelerated force that gives the weight of the body in the absence of gravity. Since it is necessary to calculate the single things in physics, simply compare it to other related things to obtain an accurate opinion on mass. The term matter refers to mass.

What is Volume?

The volume of an object is the amount of space it occupies. Simply displays the total amount of space occupied by the specific object. You can easily distinguish things by remembering formulas, and the difference table allows you to compare and understand things quickly.

Difference between mass and volume | Mass vs Volume:

Definition:

The physical value of an object is its mass, and its geometric value is its volume.

Unit:

The mass is measured using the kilogram unit, while the volume is measured using the cubic meter unit.

Object:

The mass of an object represents its matter, while the volume represents the space occupied by the object.

Persistent:

The mass is a fixed or persistent property, while the volume varies depending on the substance.

Property:

Mass is always thought of as a constant or regular property of a body or object. A body or mater will always have mass. While the volume of a substance changes depending on its state, whether solid, liquid or gaseous.

Calculations:

Mass is measured using two values. But the volume is calculated using three dimensions.

Explore more information:

Subscribe to: Comments (Atom)